Ensurepass

 

1.       QUESTION

Refer to the exhibit:

clip_image001

Which three statements are true about how router JAX will choose a path to the 10.1.3.0/24 network when different routing protocols are configured? (Choose three.)

 

A.  By default, if RIPv2 is the routing protocol, only the path JAX-ORL will be installed into the routing table.

B.  The equal cost paths JAX-CHI-ORL and JAX- NY-ORL will be installed in the routing table if RIPv2 is the routing protocol.

C.  When EIGRP is the routing protocol, only the path JAX-ORL will be installed in the routing table by default.

D.  When EIGRP is the routing protocol, the equal cost paths JAX-CHI-ORL, and JAX-NY-ORL will be installed in the routing table by default.

E.  With EIGRP and OSPF both running on the network with their default configurations, the EIGRP paths will be installed in the routing table.

F.  The OSPF paths will be installed in the routing table, if EIGRP and OSPF are both running on the network with their default configurations.

 

Answer: ADE

 

 

2.       QUESTION

Refer to the exhibit

clip_image003

The network administrator must establish a route by which London workstations can forward traffic to the Manchester workstations. What is the simplest way to accomplish this?

 

A.  Configure a dynamic routing protocol on London to advertise all routes to Manchester.

B.  Configure a dynamic routing protocol on London to advertise summarized routes to Manchester.

C.  Configure a dynamic routing protocol on Manchester to advertise a default route to the London router.

D.  Configure a static default route on London with a next hop of 10.1.1.1.

E.  Configure a static route on London to direct all traffic destined for 172.16.0.0/22 to 10.1.1.2. F.  Configure Manchester to advertise a static default route to London.

 

Answer: E

 

 

3.       QUESTION

Refer to the output of the corporate router routing table shown in the graphic:

clip_image004

The corporate router receives an IP packet with a source IP address of 192.168.214.20 and a destination address of 192.168.22.3. What will the router do with this packet?

 

A.  It will encapsulate the packet as Frame Relay and forward it out interface Serial 0/0.117.

B.  It will discard the packet and send an ICMP Destination Unreachable message out interface

FastEthernet 0/0.

C.  It will forward the packet out interface Serial 0/1 and send an ICMP Echo Reply message out interface serial 0/0.102.

D.  It will change the IP packet to an ARP frame and forward it out FastEthernet 0/0.

 

Answer: B

 

 

4.       QUESTION

Users on the 172.17.22.0 network cannot reach the server located on the 172.31.5.0 network. The network administrator connected to router Coffee via the console port, issued the show ip route command, Based on the output of the show ip route command and the topology shown in the graphic, what is the cause of the failure?

clip_image006

 

A.     The network has not fully converged.

B.     IP routing is not enabled.

C.     A static route is configured incorrectly.

D.     The FastEthernet interface on Coffee is disabled.

E.      The neighbor relationship table is not correctly updated.

F.      The routing table on Coffee has not updated .

 

Answer: C

 

 

5.       QUESTION

Which command is used to configure a default route?

 

A.  ip route 172.16.1.0 255.255.255.0 0.0.0.0

B.  ip route 172.16.1.0 255.255.255.0 172.16.2.1

C.  ip route 0.0.0.0 255.255.255.0 172.16.2.1

D.  ip route 0.0.0.0 0.0.0.0 172.16.2.1

 

Answer: D

 

 

6.       QUESTION

If IP routing is enabled, which two commands set the gateway of last resort to the default gateway? (Choose two.)

 

A.  ip default-gateway 0.0.0.0

B.  ip route 172.16.2.1 0.0.0.0 0.0.0.0

C.  ip default-network 0.0.0.0

D.  ip default-route 0.0.0.0 0.0.0.0 172.16.2.1

E.  ip route 0.0.0.0 0.0.0.0 172.16.2.1

 

Answer: CE

 

 

7.       QUESTION

What must be set correctly when configuring a serial interface so that higher-level protocols calculate the best route?

 

A.  bandwidth

B.  delay

C.  load

D.  reliability

 

Answer: A

 

 

8.       QUESTION

What are two characteristics of RIPv2? (Choose two.)

 

A.  classful routing protocol

B.  variable-length subnet masks

C.  broadcast addressing

D.  manual route summarization

E.  uses SPF algorithm to compute path

 

Answer: BD

 

 

9.       QUESTION

What two things will a router do when running a distance vector routing protocol? (Choose two.)

 

A.     Send periodic updates regardless of topology changes.

B.     Send entire routing table to all routers in the routing domain.

C.     Use the shortest-path algorithm to the determine best path.

D.     Update the routing table based on updates from their neighbors.

E.      Maintain the topology of the entire network in its database.

 

Answer: AD

 

 

10.   QUESTION

Refer to the exhibit:

 

clip_image007

Which (config-router) command will allow the network represented on the interface to be advertised by RIP?

 

A.  redistribute ethernet0

B.  network ethernet0

C.  redistribute 10.12.0.0

D.  network 10.12.0.0

 

Answer: D

 

Ensurepass offers Latest 2013 640-802 Real Exam Questions , help you to pass exam 100%.

Comments are closed.