Ensurepass

 

 

1.       QUESTION

Refer to the exhibit:

clip_image002

What information can be gathered from the output?

 

A.  One router is running RIPv1.

B.  RIP neighbor is 224.0.0.9.

C.  The network contains a loop.

D.  Network 10.10.1.0 is reachable.

 

Answer: D

 

 

2.       QUESTION

Use the output from the router shown in the graphic above to determine which of the following are correct. (Choose two.)

clip_image003

A.     Router John uses a link-state routing protocol.

B.     Router John will receive routing updates on the Serial0/0 interface.

C.     Router John will receive routing updates on the Serial0/1 interface.

D.     Router John will send routing updates out the Serial0/0 interface.

E.      Router John will send routing updates out the FastEthernet0/0 interface.

F.      Router John will send routing updates out the Serial0/1 interface.

 

Answer: BD

 

 

3.       QUESTION

Which series of commands will configure router R1 for LAN-to-LAN communication with router R2? The enterprise network address is 192.1.1.0/24 and the routing protocol in use is RIPv2. (Choose three.)

clip_image004

A.     R1(config)# interface ethernet 0

R1(config-if)# ip address 192.1.1.129 255.255.255.192

R1(config-if)# no shutdown

 

B.     R1(config)# interface ethernet 0

R1(config-if)# ip address 192.1.1.97 255.255.255.192

R1(config-if)# no shutdown

 

C.     R1(config)# interface serial 0

R1(config-if)# ip address 192.1.1.4 255.255.255.252

R1(config-if)# clock rate 56000

 

D.     R1(config)# interface serial 0

R1(config-if)# ip address 192.1.1.6 255.255.255.252

R1(config-if)# no shutdown

 

E.      R1(config)# router rip

R1(config-router)# network 192.1.1.4

R1(config-router)# network 192.1.1.128

 

F.      R1(config)# router rip

R1(config-router)# version 2

R1(config-router)# network 192.1.1.0

 

Answer: ADF

 

 

4.       QUESTION

Which routing protocols can be used within the enterprise network shown in the diagram? (Choose three.)

clip_image005

 

A.     RIP v1

B.     RIP v2

C.     IGRP

D.     OSPF

E.      BGP

F.      EIGRP

 

Answer: BDF

 

 

5.       QUESTION

Which routing protocols will support the following IP addressing scheme? (Choose three.)

 

Network 1 – 192.168.10.0 /26

Network 2 – 192.168.10.64 /27

Network 3 – 192.168.10.96 /27

Network 4 – 192.168.10.128 /30

Network 5 – 192.168.10.132 /30

 

A.  RIP version 1

B.  RIP version 2

C.  IGRP

D.  EIGRP

E.  OSPF

 

Answer: BDE

 

 

6.       QUESTION

Refer to the graphic:

clip_image006

Host 1 cannot receive packets from Host 2. Assuming that RIP v1 is the routing protocol in use, what is wrong with the IP configuration information shown? (Choose two.)

 

A.     The fa0/1 interface of router R2 has been assigned a broadcast address.

B.     The fa0/1 network on router R2 overlaps with the LAN attached to R1.

C.     Host 2 has been assigned the incorrect subnet mask.

D.     Host 1 has been configured with the 255.255.248.0 subnet mask.

E.      Host 2 on router R2 is on a different subnet than its gateway.

 

Answer: BC

 

 

7.       QUESTION

Refer to the exhibit:

clip_image007

Host A is to send data to Host B. How will Router1 handle the data frame received from Host A? (Choose three.)

 

A.     Router1 will strip off the source MAC address and replace it with the MAC address on the forwarding FastEthernet interface.

B.     Router1 will strip off the source IP address and replace it with the IP address on the forwarding FastEthernet interface.

C.     Router1 will strip off the destination MAC address and replace it with the MAC address of Host B.

D.     Router1 will strip off the destination IP address and replace it with the IP address of Host B.

E.      Router1 will forward the data frame out interface FastEthernet0/1.

F.      Router1 will forward the data frame out interface FastEthernet0/2.

 

Answer: ACF

 

 

8.       QUESTION

What can be determined from the line of show ip route output shown in the exhibit? (Choose two.)

clip_image009

A.  The next routing update can be expected in 35 seconds.

B.  The IP address 10.10.10.6 is configured on S0/1.

C.  The IP address 10.10.10.8 is configured on S0/1.

D.  This route is using the default administrative distance.

E.  The 10.10.10.8 network is two hops away from this router.

 

Answer: DE

 

 

9.       QUESTION

What is an appropriate use of a default route?

 

A.  to provide routing to a local web server

B.  to provide routing from an ISP to a stub network

C.  to provide routing that will override the configured dynamic routing protocol

D.  to provide routing to a destination that is not specified in the routing table and which is outside the local network

 

Answer: D

 

 

10.   QUESTION

Refer to the exhibit:

clip_image011

 

Two routers have just been configured by a new technician. All interfaces are up. However, the routers are not sharing their routing tables. What is the problem?

 

A.     Split horizon is preventing Router2 from receiving routing information from Router1.

B.     Router1 is configured for RIP version 2 and Router2 is configured for RIP version 1.

C.     Router1 has an ACL that is blocking RIP version 2.

D.     There is a physical connectivity problem between Router1 and Router2.

E.      Router1 is using authentication and Router2 is not.

 

Answer: B

 

Ensurepass offers Latest 2013 640-802 Real Exam Questions , help you to pass exam 100%.

Comments are closed.