Ensurepass

1.       QUESTION

Refer to the exhibit:

clip_image001

 

Which two statements are true about interVLAN routing in the topology that is shown in the exhibit? (Choose two.)

 

A.  Host E and host F use the same IP gateway address.

B.  Router1 and Switch2 should be connected via a crossover cable.

C.  Router1 will not play a role in communications between host A and host D.

D.  The FastEthernet 0/0 interface on Router1 must be configured with subinterfaces.

E.  Router1 needs more LAN interfaces to accommodate the VLANs that are shown in the exhibit.

F.  The FastEthernet 0/0 interface on Router1 and Switch2 trunk ports must be configured using the same encapsulation type.

 

Answer: DF

 

 

2.       QUESTION

A network administrator is explaining VTP configuration to a new technician. What should the network administrator tell the new technician about VTP configuration? (Choose three.)

 

A.  A switch in the VTP client mode cannot update its local VLAN database.

B.  A trunk link must be configured between the switches to forward VTP updates.

C.  A switch in the VTP server mode can update a switch in the VTP transparent mode.

D.  A switch in the VTP transparent mode will forward updates that it receives to other switches.

E.  A switch in the VTP server mode only updates switches in the VTP client mode that have a higher VTP

revision number.

F.  A switch in the VTP server mode will update switches in the VTP client mode regardless of the configured VTP domain membership.

 

Answer: ABD

 

 

3.       QUESTION

A company is installing IP phones. The phones and office computers connect to the same device. To ensure maximum throughput for the phone data, the company needs to make sure that the phone traffic is on a different network from that of the office computer data traffic. What is the best network device to which to directly connect the phones and computers, and what technology should be implemented on this

device? (Choose two.)

 

A. hub

B. router

C. switch

D. STP

E. subinterfaces

F. VLAN

 

Answer: CF

 

 

4.       QUESTION

Refer to the exhibit:

 

clip_image002

A network associate needs to configure the switches and router in the graphic so that the hosts in VLAN3 and VLAN4 can communicate with the enterprise server in VLAN2. Which two Ethernet segments would need to be configured as trunk links? (Choose two.)

 

A.     A

B.     B

C.     C

D.     D

E.      E

F.      F

 

Answer: CF

 

 

5.       QUESTION

Refer to the exhibit:

 

clip_image003

 

A network administrator is adding two new hosts to Switch A. Which three values could be used for the configuration of these hosts? (Choose three.)

 

 

A.     host A IP address: 192.168.1.79

B.     host A IP address: 192.168.1.64

C.     host A default gateway: 192.168.1.78

D.     host B IP address: 192.168.1.128

E.      host B default gateway: 192.168.1.129

F.      host B IP address: 192.168.1.190

 

Answer: ACF

 

 

6.       QUESTION

Which three statements are typical characteristics of VLAN arrangements? (Choose three.)

 

A.  A new switch has no VLANs configured.

B.  Connectivity between VLANs requires a Layer 3 device.

C.  VLANs typically decrease the number of collision domains.

D.  Each VLAN uses a separate address space.

E.  A switch maintains a separate bridging table for each VLAN.

F.  VLANs cannot span multiple switches.

 

Answer: BDE

 

 

7.       QUESTION

Which three of these statements regarding 802.1Q trunking are correct? (Choose three.)

 

A.  802.1Q native VLAN frames are untagged by default.

B.  802.1Q trunking ports can also be secure ports.

C.  802.1Q trunks can use 10 Mb/s Ethernet interfaces.

D.  802.1Q trunks require full-duplex, point-to-point connectivity.

E.  802.1Q trunks should have native VLANs that are the same at both ends.

 

Answer: ACE

 

 

8.       QUESTION

By default, each port in a Cisco Catalyst switch is assigned to VLAN1. Which two recommendations are key to avoid unauthorized management access? (Choose two.)

 

A.     Create an additional ACL to block the access to VLAN 1.

B.     Move the management VLAN to something other than default.

C.     Move all ports to another VLAN and deactivate the default VLAN.

D.     Limit the access in the switch using port security configuration.

E.      Use static VLAN in trunks and access ports to restrict connections.

F.      Shutdown all unused ports in the Catalyst switch.

 

Answer: BF

 

 

9.       QUESTION

What is the name of the VTP mode of operation that enables a switch to forward only VTP advertisements while still permitting the editing of local VLAN information?

 

A.  server

B.  client

C.  tunnel

D.  transparent

 

Answer: D

 

 

10.   QUESTION

Which two benefits are provided by creating VLANs? (Choose two.)

 

A.  added security

B.  dedicated bandwidth

C.  provides segmentation

D.  allows switches to route traffic between subinterfaces

E.  contains collisions

 

Answer: AC

 

Ensurepass offers Latest 2013 640-802 Real Exam Questions , help you to pass exam 100%.

Comments are closed.