Ensurepass

 

1.       QUESTION

A system administrator types the command to change the hostname of a router. Where on the Cisco IFS is that change stored?

 

A.  NVRAM

B.  RAM

C.  FLASH

D.  ROM

E.  PCMCIA

 

Answer: B

 

 

2.       QUESTION

Refer to the exhibit:

 

clip_image002

If number 2 is selected from the setup script, what happens when the user runs setup from a privileged prompt?

 

A.  Setup is additive and any changes will be added to the config script.

B.  Setup effectively starts the configuration over as if the router was booted for the first time.

C.  Setup will not run if an enable secret password exists on the router.

D.  Setup will not run, because it is only viable when no configuration exists on the router.

 

Answer: A

 

 

3.       QUESTION

Refer to the exhibit:

 

clip_image004

What can be determined about the router from the console output?

 

A.  No configuration file was found in NVRAM.

B.  No configuration file was found in flash.

C.  No configuration file was found in the PCMCIA card.

D.  Configuration file is normal and will load in 15 seconds.

 

Answer: A

 

 

4.       QUESTION

Refer to the exhibit:

 

clip_image005

What can be determined from the output?

 

A.  192.168.1.2 is local to the router.

B.  192.168.3.1 is local to the router.

C.  192.168.1.2 will age out in less than 1 minute.

D.  192.168.3.1 has aged out and is marked for deletion.

 

Answer: B

 

 

5.       QUESTION

Which router IOS commands can be used to troubleshoot LAN connectivity problems? (Choose three.)

 

A.     ping

B.     tracert

C.     ipconfig

D.     show ip route

E.      winipcfg

F.      show interfaces

 

Answer: ADF

 

 

6.       QUESTION

What functions do routers perform in a network? (Choose two.)

 

A.     packet switching

B.     access layer security

C.     path selection

D.     VLAN membership assignment

E.      bridging between LAN segments

F.      micro segmentation of broadcast domains

 

Answer: AC

 

 

7.       QUESTION

Refer to the partial command output shown:

clip_image006

Which two statements are correct regarding the router hardware? (Choose two.)

 

A.     Total RAM size is 32 KB.

B.     Total RAM size is 16384 KB (16 MB).

C.     Total RAM size is 65536 KB (64 MB).

D.     Flash size is 32 KB.

E.      Flash size is 16384 KB (16 MB).

F.      Flash size is 65536 KB (64 MB).

 

Answer: CE

 

 

8.       QUESTION

How does using the service password encryption command on a router provide additional security?

 

A.     by encrypting all passwords passing through the router

B.     by encrypting passwords in the plain text configuration file

C.     by requiring entry of encrypted passwords for access to the device

D.     by configuring an MD5 encrypted key to be used by routing protocols to validate routing exchanges

E.      by automatically suggesting encrypted passwords for use in configuring the router

 

Answer: B

 

 

 

9.       QUESTION

Refer to the exhibit:

clip_image007

Host in network 192.168.2.0 are unable to reach hosts in network 192.168.3.0. Based on the output from

Router A, what are two possible reasons for the failure? (Choose two.)

 

A.     The cable that is connected to S0/0 on Router A is faulty.

B.     Interface S0/0 on Router B is administratively down.

C.     Interface S0/0 on Router A is configured with an incorrect subnet mask.

D.     The IP address that is configured on S0/0 of Router B, is not in the correct subnet.

E.      Interface S0/0 on Router A is not receiving a clock signal.

F.      The encapsulation that is configured on S0/0 of Router B does not match the encapsulation that is configured on S0/0 of Router A.

 

Answer: EF

 

 

10.   QUESTION

Refer to the diagram:

clip_image009

What is the largest configuration file that can be stored on this router?

 

A.       191K bytes

B.  16384K bytes

C.  31369K bytes

D.  114688K bytes

 

Answer: A

 

Ensurepass offers Latest 2013 640-802 Real Exam Questions , help you to pass exam 100%.

 

Comments are closed.