1. QUESTION
Refer to the exhibit.
Which user-mode password has just been set?
A. Telnet
B. Auxiliary
C. SSH
D. Console
Answer: A
2. QUESTION
Which two locations can be configured as a source for the IOS image in the boot system command? (Choose two.)
A. RAM
B. NVRAM
C. flash memory
D. HTTP server
E. TFTP server
F. Telnet server
Answer: CE
3. QUESTION
What are two reasons a network administrator would use CDP? (Choose two.)
A. to verify the type of cable interconnecting two devices
B. to determine the status of network services on a remote device
C. to obtain VLAN information from directly connected switches
D. to verify Layer 2 connectivity between two devices when Layer 3 fails
E. to obtain the IP address of a connected device in order to telnet to the device
F. to determine the status of the routing protocols between directly connected routers
Answer: DE
4. QUESTION
A network administrator changes the configuration register to 0x2142 and reboots the router. What are two results of making this change? (Choose two.)
A. The IOS image will be ignored.
B. The router will prompt to enter initial configuration mode.
C. The router will boot to ROM.
D. Any configuration entries in NVRAM will be ignored.
E. The configuration in flash memory will be booted.
Answer: BD
5. QUESTION
QoS policies are applied on the switches of a LAN. Which type of command will show the effects of the policy in real time?
A. show command
B. debug command
C. configuration command
D. rommon command
Answer: B
6. QUESTION
Which command is used to debug a ping command?
A. debug icmp
B. debug ip icmp
C. debug tcp
D. debug packet
Answer: B
7. QUESTION
Which command displays CPU utilization?
A. show protocols
B. show process
C. show system
D. show version
Answer: B
8. QUESTION
Which command reveals the last method used to powercycle a router?
A. show reload
B. show boot
C. show running-config
D. show version
Answer: D
9. QUESTION
Refer to the exhibit:
You are connected to the router as user Mike. Which command allows you to see output from the OSPF debug command?
A. terminal monitor
B. show debugging
C. show sessions
D. show ip ospf interface
Answer: A
10. QUESTION
The switches shown in the diagram, Core and Core2, are both Catalyst 2950s. The addressing scheme for each company site is as follows:
l Router Ethernet port – 1st usable address
l Core – 2nd usable address
l Core2 – 3rd usable address
For this network, which of the following commands must be configured on Core2 to allow it to be managed remotely from any subnet on the network? (Choose three.)
A. Core2(config)# interface f0/0
Core2(config-if)# ip address 192.168.1.10 255.255.255.248
B. Core2(config)# interface vlan 1
Core2(config-if)# ip address 192.168.1.11 255.255.255.248
C. Core2(config)# line con 0
Core2(config-line)# password cisco
D. Core2(config)# line vty 0 4
Core2(config-line)# password cisco
E. Core2(config)# ip default-gateway 192.168.1.9
F. Core2(config)# ip route 0.0.0.0 0.0.0.0 192.168.1.8
Answer: BDE
Ensurepass offers Latest 2013 640-802 Real Exam Questions , help you to pass exam 100%.
100-105 Dumps VCE PDF
200-105 Dumps VCE PDF
300-101 Dumps VCE PDF
300-115 Dumps VCE PDF
300-135 Dumps VCE PDF
300-320 Dumps VCE PDF
400-101 Dumps VCE PDF
640-911 Dumps VCE PDF
640-916 Dumps VCE PDF
70-410 Dumps VCE PDF
70-411 Dumps VCE PDF
70-412 Dumps VCE PDF
70-413 Dumps VCE PDF
70-414 Dumps VCE PDF
70-417 Dumps VCE PDF
70-461 Dumps VCE PDF
70-462 Dumps VCE PDF
70-463 Dumps VCE PDF
70-464 Dumps VCE PDF
70-465 Dumps VCE PDF
70-480 Dumps VCE PDF
70-483 Dumps VCE PDF
70-486 Dumps VCE PDF
70-487 Dumps VCE PDF
220-901 Dumps VCE PDF
220-902 Dumps VCE PDF
N10-006 Dumps VCE PDF
SY0-401 Dumps VCE PDF